Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision		Previous revision
wireless_network [2007-07-12 11:07] – external edit 127.0.0.1wireless_network [2007-07-30 11:01] (current) – 192.168.1.133
Line 1: Line 1:
  
-Wireless Network(s/ing)+===== Wireless Network(s/ing) =====
  
  
  
-general info (802.11 related)+ 
 +==== general info (802.11 related) ==== 
  
  
Line 20: Line 22:
   * access point utilities for GNU/linux http://ap-utils.polesye.net/   * access point utilities for GNU/linux http://ap-utils.polesye.net/
  
-community based wireless networks 
  
-the Consume project is creating a decentralised, wireless network in london ec2 area, nodes are contributed voluntarily. http://consume.net/consume.html +==== community based wireless networks ==== 
-BYTE: A WirelessNeighborhoodFreenet  + 
-http://www.byte.com/documents/s=1436/byt20010926s0003/1001_bar.html +  * the Consume project is creating a decentralised, wireless network in london ec2 area, nodes are contributed voluntarily. http://consume.net/consume.html 
-search engine for wireless nets based on gps info http://www.shmoo.com/gawd/ +  * BYTE: A [[Wireless Neighborhood Freenet]] >> http://www.byte.com/documents/s=1436/byt20010926s0003/1001_bar.html 
-directory + info http://wirelessanarchy.com/ and http://freenetworks.org/ +  * search engine for wireless nets based on gps info http://www.shmoo.com/gawd/ 
-http://www.wlan.org.uk/+  * directory + info http://wirelessanarchy.com/ and http://freenetworks.org/ 
 +  * http://www.wlan.org.uk/
  
 in .au in .au
-sydney http://www.sydneywireless.com/db2/  +  * sydney http://www.sydneywireless.com/db2/  
-canberra http://www.air.net.au/  +  * canberra http://www.air.net.au/  
-brisbane http://www.csee.uq.edu.au/~mesh/  +  * brisbane http://www.csee.uq.edu.au/~mesh/  
-melbourne http://melbwireless.dyndns.org/ +  * melbourne http://melbwireless.dyndns.org/ 
  
 in brussels in brussels
-http://bombolong.aisbl.org/ +  * http://bombolong.aisbl.org/ 
-reseau citoyen+  * reseau citoyen
  
-tools for finding/mapping/hacking wireless networks 
-http://netstumbler.org/  
-http://airsnort.sourceforge.net/  
-wireless network visualisation http://www.ittc.ku.edu/wlan/  
  
-antennas / mods+====tools for finding/mapping/hacking wireless networks==== 
 +  * http://netstumbler.org/  
 +  * http://airsnort.sourceforge.net/  
 +  * wireless network visualisation http://www.ittc.ku.edu/wlan/  
 +  * kismac, on the macbook > http://www.kismetwireless.net/Forum/Equipment/Messages/1170919945.7235651 
 + 
 +==== antennas / mods ==== 
 homebrew antenna shootout (using tin cans for higer dBm!) http://www.turnpoint.net/wireless/has.html  homebrew antenna shootout (using tin cans for higer dBm!) http://www.turnpoint.net/wireless/has.html 
 waveguide antenna http://www.oreillynet.com/cs/weblog/view/wlg/1124  waveguide antenna http://www.oreillynet.com/cs/weblog/view/wlg/1124 
Line 52: Line 57:
 http://kevlar.burdell.org/~will/antenna/ http://kevlar.burdell.org/~will/antenna/
  
-protocols+==== protocols ==== 
  
 GPRS GPRS
Line 66: Line 72:
  
  
-unsorted notes+==== unsorted notes ==== 
  
 For doing this type of war driving, you don't need to actually connect to each AP. The card is put into a low-level promiscuous mode, so it can receive all packets. Every AP sends out a continuous stream of 'beacon' packets which the software can use to determine what networks are available. Also, at least on Prism-based cards, you get both a signal and noise measure for every packet received. So you just drive around snarfing up packets, and every one you get you can check for the source MAC address (to determine the AP) and the S/N ratio. No need to talk to the AP's at all, it's totally passive. For doing this type of war driving, you don't need to actually connect to each AP. The card is put into a low-level promiscuous mode, so it can receive all packets. Every AP sends out a continuous stream of 'beacon' packets which the software can use to determine what networks are available. Also, at least on Prism-based cards, you get both a signal and noise measure for every packet received. So you just drive around snarfing up packets, and every one you get you can check for the source MAC address (to determine the AP) and the S/N ratio. No need to talk to the AP's at all, it's totally passive.

User Tools

Page Tools

Site Tools